Alarm Clock
Instruction For Use
Table of Contents
Preface and Quality Assurance
Using instruction for Chinese time signal clock
DV Structure diagram
DV product introduction & handling instruction
DV File storage instruction
Relevant parameters of DV
Power source and fittings
Troubleshooting
Precautions
Preface
This Instruction will guide you how to use the product. Meanwhile it provides
the necessary information related to the product, such as the information for operating
and handling. You are recommended to read the Instruction carefully and
understand all contents herein before operating. Please keep the Instruction
carefully. We hope this product satisfied with your demand and sever you better.
Product Assurance
This product is with FCC and CE certificate and had inspected by the authorized
organizations where was found to comply with the recommended indexes. User is
under our safety assurance when operating this product.
Instruction For Use for Time-signal Clock
I. Basic functions
1. 5 buttons: HR, MIN, SET, LIGHT,
TALK/SNZ;
2. The time
& minute can be displayed in a 3.5 bit LCD panel. Time-showing system of 12
hours and 24 hours is available;
3. Multiple
rings for choice: Beep, cock, etc. 5 melodies for option.
4. The time
alarm will be triggered every 10 minutes if the clock is on the snooze function. It can alarm 6 times maximally.
5. Two
on-the-hour alarm functions for choice;
6. The ring of
“Beep” will be become louder generally. And it will last 1 minute;
7. If adopting
the melody as the ring, the clock will alarm when the melody ends.
II. Function operation
1. When switching the power on, the
whole LCD will display; after the ring of a melody ends, the clock will display
time;
2. Press “Set”
button under the Time mode to set as per the following sequences (the display
will flash simultaneously):
Time setting → Alarm setting →
On-the-hour alarm setting
3. Press “HR” button under the Time
Setting mode to set hour and “MIN” button to set minute;
4. Press “HR” button under the Alarm
Setting mode (Symbol: 
) to set hour and “MIN” button to set minute. Press “SNZ”
button when alarming, the clock will re-alarm every 10 minutes, and will send
alarm by 6 times at most;
5. Under the On-the-hour Alarm Setting
mode (the symbol of alarm and the on-the-hour alarm will flash):
It will open and close the function
(Symbol: 
) by pressing the “HR” button, but send alarm
during the time from 
); it can activate the inactivate the alarm
ring by pressing “MIN” button (Symbol: 
).
6. Under the Time Mode and if the “HR” button is pressed, it can shift
the hour system (12/24 hour system); by pressing “MIN” button, it can select
the alarm ring.
7. Under any modes, it can turn the
background light off by pressing the “LIGHT” button.
8. Under any modes, it can report the
time by pressing the “TALK” button.
DV Using Instruction
1、Alarm Clock
I. Structure Diagram
Time-telling button
Lens TF card Rotational cover
Ti
Turn off
Turn on
Switch button Sender
Video
motion detection video
II. Product Introduction
This product is a high-resolution 30-frame (640X480, 1280*960) remote video surveillance clock, with an
external TF Card. As a multifunctional high-tech product, the product is
available multiple functions, such as: video, sound recording, induction video,
take a photo, cyber chat, electric alarm clock and file storage; with the
high-capacity battery, it can last recording for about 12 hours continuously
and audio recording for 25 hours continuously; besides, the product can replace
the high-resolution video with 2 million pixels, sound and file automatically,
Meanwhile, the product is designed the multiple languages for telling the time.
It supports 32GB storage. Its TF card can be used for a long time and remote
controller can be easy to handle. With the best imperceptibility, this product
will be as your ideal assistant to prevent theft and get evidence.
III. Handling Instructions
1.
Open
the rotational cover at the right side, insert the TF card and turn “ON” to get
ready.
2.
Use
the remote controller to aim to the receiver of the clock and press " 
"
to start. When the blue lamp is on and the clock is under the stand by mode.
3.
Press 
to
start recording video. After the blue lamp flashes 3 times and then turns off,
it start recording. stop pressing , it
will save the video file and return to the “holding state” , and the blue lamp
will be on (the default time length for video recorded is 20 minutes).
4.
Press 
button
to start recording a sound; after the blue lamp flashes 1 time and turns off,
it will be put into the working order; Press again, it will save the sound file and return to the
“holding state” , and the blue lamp will be on (the default time length for
sound recorded is 20 minutes);
5.
Press 
button
to get in photo taking mode. It will take a photo if pressing this button again.
When pressing this button, the blue lamp will flash; after taking the photo, it
will return to the stand by.
6.
Press 
button
to get in motion detection mode, then the blue lamp will flash quickly. If a
moving object is detected, the blue lamp will flash slowly by two times and the
device will be start to record video. If there is no moving object to be
detected, the blue lamp will return to “Quick-flash: and get in motion
detection mode (the default length for the video file is 3 minutes);
7.
Press 
button,
it will turn the device off and the blue lamp will be off.
8.
When
the switch is “ON”, insert the USB cable and then press button
on the remote controller, the device will access to the U-disc mode.
9.
PC
camera function: Please install the driver software which is saved in the
Compact Disc before operating; Turn on the device by pressing on the
remote controller when the device is under the mode of “ON”, insert USB cable
to connect the computer; at this time, it will access to PC CAM mode;
10. Charging: Place the chief switch to “OFF”
position, insert USB adapter, and the red lamp will be on; When it is full, the
red lamp will be off. You can charge it too by connect this device to a
computer (
Please use only the adapter provided with
the device together; if the device getting hot or occurs other unexpected
situations whilst charging, please disconnect the adapter's power source);
11. Reset: If the product stops working under
illegal operation or other unclear reasons, please place the switch of the
device to “OFF” position, and then to “ON” position. It will reset the product
accordingly;
12. When the battery is low capacity, the blue
lamp will keep flashing or the screen display will be unclear. Then please
charge it immediately. If it is used off, the file will be saved automatically;
13. Recorder date: Run the writertime file( in
CD disc) when the camera connect with computer. And then ,the video time is the
same computer.
14. File update: please install “Network Installer”
from the installation disc; use the remote controller to open the clock, and
then insert the USB cable in 10 seconds; afterwards, the computer will open an
interface automatically; click “Program Upgrade”, it will open a dialogue box;
afterwards click “Update”.
When ① DRAM Timing, select 0X35
When ② DRAM Size, select “
15. When the program is lost, please install
the software which is saved in the Compact Disc, and then click “STK02NU
Programme Upgrading Tool”, afterwards click “Update”;
Under ① DRAM Timing, select 0X35
Under ② DRAM Size, select “
IV. File’s storage and play
When finishing video-recording and other operations,
please place the switch to “ON” position, connect it to your computer by USB
cable, and press 
on the
remote controller; copy the file or cut and paste it to the your computer to
play; or you can remove the TF card and use the card reader to read the data
inside.
The Media player / KM player is recommended.
USB port of computer USB data cable
V. Precautions
Application conditions: Please abide by the related national laws and
regulations strictly; it is prohibited to use the product for illegal purpose,
otherwise you must be responsible for the consequences.
Software upgrade: In order to keep the device available a better performance,
the manufacturer shall improve the product software continuously. The device is
designed the function to update by user itself, please claim the latest
software and upgrading method towards your local dealer.
Working temperature: Please use the device only at the natural
temperature; never use the device at the temperature that human body feels unconformable.
Working humidity: Please use the device only in the environmental humidity
suitable for living; keep the device faraway from the wet environment. This
device is not designed the water-proof function.
Video
luminance: Please use the device when the sufficient luminance is available; it
is prohibited to use the lens to aim to the sun or other intensive light
source; otherwise it may damage the optical apparatus;
Cleanliness requirement: Please do not use the device in the environment full of
dirt; otherwise it may cause the lens or other parts to attach with dirt and
influence video effect. It can use the lens wiping paper or glass cloth to
clean.
Other precautions:
This device is a precision electronic product; please keep it away intensive
impact, shock, intense magnetic field or electric field.
第十页
V. Relevant Parameters
|
Pixel |
2.0 maga pixel |
|
Resolution |
640*480、1280*960 |
|
Video format |
AVI |
|
Frame number |
30fps |
|
Vision angle |
72° |
|
Induction photographing |
6 meters for Straight-line distance |
|
Minimal illumination |
1LUX |
|
|
2200MA |
|
Continuous recording time |
Over 12 hours |
|
Remote operating distance |
|
|
Scope for sound recording |
|
|
Power consumption |
130MA / 3.7V |
|
Storage temperature |
-20~ |
|
working temperature |
-10~ |
|
working humidity |
15~85% RH |
|
Type of memory card |
|
|
Capacity of memory card |
32GB maximally |
|
Player software |
Media player / KM player |
|
USB Interface |
USB1.1/2.0 |
|
Operating system |
WIN 2000/ XP / Visat32 / 7 |
|
Time consumed of storage |
1GB/40 minutes |
|
Charging time |
About 4
hours |
Troubleshooting
|
Trouble |
Troubleshooting |
|
Can not turn on |
Remove the insulator |
|
Can not charge the electricity |
Replace the battery or adapter |
|
Blue light flashes rapidly |
re-start camera, low-power charging reminder, delete
redundant files from the card, put in TF Card or replacing TF Card. |
|
Remote controller is hard to use |
Align with the receiver’s head, remove the insulator
of remote controller, replace battery or wait for reading the card |
|
Cannot connect with computer |
Replace the data cable or computer |
|
Clock’s screen flashes or character is displayed
incompletely |
Charging |
|
Sound is recorded with noise or video is not clear |
Charging, replace TF card |
|
Other problems |
Please contact local seller |
Power Source
This product can only be allowed to comply the authorized power sources with
the following marks, i.e.:
UL
mark / American Power Certification
CE
mark / UN Power Certification
CCC
mark / Chinese Power Certification
BS
mark / British Power Certification
C-TICK
mark / Australian Power Certification
GS mark / German Power
Certification
PSE
mark / Japanese Power Certification
Note:
The power device will get a rising-temperature on the surface when operating.
This is an expected phenomenon. If it is a must to bring the power device with
you, please remove it from the power socket.
Necessary Fittings
Compact Disc Switching power supply
USB Data
Cable Instruction For Use